ST硬盘错误码表

lwj131488 · 发表于 2006-9-23 11:38:42

在检测到错误的时候硬盘输出到终端错误的代码和简短的附加信息.
例如: "Code - FE Track 19A1.3.06E Sns E00 Rty F7FF.FF.80FF Rtf 1C00" – "FE"错误.
错误代码解码表:
00 No error
03 Calculated CRC doesn't match
11 Spin error
12 Ramp load error
13 Offtrack
14 Write fault
15 Rd/wr seek timeout code
16 Seek timeout
17 "False" AMDET (mis-timed)
18 Bad burst error code
19 Bad grey code
1A Early sync code
IB Missed am
1С Failed the servo defect screen threshold
1E Target generator sector error
IF Physical sector error
20 Skip write detected using servo burst
22 NRZ freeze occurred (A=A')&(B=B')&(C=C)&P=D')
29 Thermal Asperity errors padded in test 36.
30 Data miscompares
32 Slipped write error
33 Adaptives are not loaded
34 Unexpected ECC verify read failure
35 Unexpected ECC verify read success
36 Pending block encountered during a write
37 Pending block encountered and read successfully
41 Long ECC error correction code
42 Non zero byte detected
43 Data ECC error
44 FIFO over/underrun
45 Track ID miscompare error
46 Track ID read TO code
47 Missed data sync byte
48 Missed data sync after a split
49 Thermal asperity code
4A Error didn't repeat during dynamic sparing mini cert
4B Error log full
4C Controller stopped without a reason
4D Error reassigned during dynamic sparing
4E Block release timeout error
4F Buffer ready error
50 Slipped sector
51 Alternated sector
52 Pad and fill defects
53 Hard error w/AT retries no error with full retries
54 Error during scratchfill
55 Bad alt dest ID info
56 Unable to find valid alt dest
57 Unable to delete alt dest
58 Too many defects per head
59 Too many defects per track
5A Too many dynamic slips
5C Unknown full slip failure
5E Pad and fill defects
5F Entire defect span was not found in User Defect List
60 No spares available
61 Write blocked w/o a reason
62 Write gate came on early
63 Write gate went off late
64 GC thermal sensor fault detected
65 Shock sensor fault detected
66 Attempt made to write at the wrong target location.
68 FW initiated disc sequencer reset
69 FW sequencer abort; split sector runaway RG
70 Bad disc resident cert/diag code
71 Unable to read system sectors code
72 Unable to read packwriter auto-stamp
73 Invalid defect info loaded
74 Invalid alt info table
88 Unable to learn good zap on track
89 Cylinder to be skipped out in loopback test
8A Wedge slipped
8B Write ID failed 8C Cylinder padded 8D Cylinder filled in
8E Cylinder skipped out
8F Max cylinder skips has been reached
90 Zapped burst
912 consecutive zapped bursts
92 Too many zapped bursts on a track
93 Unable to zap - 2 consecutive bad bursts
94 Sumsquare of PES on this track exceeds limit
95 Unable to zap bad burst
96 Too many position plus velocity threshold breaks
97 Zapped splice code
98 Encroachment code
99 Max number of slipped tracks have been reached
9A The slipped cyl requested does not exist.
9B Head switch timeout error code
АО Preamp miscommunication
Al Reserve track defect list bad
A2 Boot adaptives bad
A3 Bad application code
A4 Not enough sectors saved to the disc for adaptives
A5 Application code check sum error
A6 Application code not compatible
CE Cert test passed
CF Cert test failed
ED Attempt to write the user slip list but no valid list
FB Missing critical parameter
FC Command aborted (internal only)
FD R/w command rejected
FE Invalid address passed to Niwot
FA Un-initialized preamp code for new preamp interface
FF Unsupported code in the new preamp interface