7代砍头的问题！

happyevery · 发表于 2010-6-27 11:52:27

7代盘，可能0头有问题，于是我就加了外部ROM，写了1头启动ROM后；在加载了1#单头的LDR，然后编辑SN，然后我在8级下C20可发现SN不是我新改的SN，没有管它开跑SF，请朋友们帮你看看以下的信息：
T>Age=60 Type=20 MxCyl=16358 MxHd=0 MxSct=44C BSz=0000 TCode=0000
N50,,22
T>#
Enter Drive S/N  5JX12345
Enter Packwriter S/N 5JX12345
T>/8
8>C20
(SN: 5JVW49CJ)
8>/t
T>N2,AA,22
T>No valid SeaDex script in buffer.
Begin Test 02
ASCII logging on

                  Not Power Cycling

                  Not Power Cycling
Zone 00 Head 00 adaptives set to defaults
Zone 00 Head 01 adaptives set to defaults
Zone 01 Head 00 adaptives set to defaults
Zone 01 Head 01 adaptives set to defaults
Zone 02 Head 00 adaptives set to defaults
Zone 02 Head 01 adaptives set to defaults
Zone 03 Head 00 adaptives set to defaults
Zone 03 Head 01 adaptives set to defaults
Zone 04 Head 00 adaptives set to defaults
Zone 04 Head 01 adaptives set to defaults
Zone 05 Head 00 adaptives set to defaults
Zone 05 Head 01 adaptives set to defaults
Zone 06 Head 00 adaptives set to defaults
Zone 06 Head 01 adaptives set to defaults
Zone 07 Head 00 adaptives set to defaults
Zone 07 Head 01 adaptives set to defaults
Zone 08 Head 00 adaptives set to defaults
Zone 08 Head 01 adaptives set to defaults
Zone 09 Head 00 adaptives set to defaults
Zone 09 Head 01 adaptives set to defaults
Zone 0A Head 00 adaptives set to defaults
Zone 0A Head 01 adaptives set to defaults
Zone 0B Head 00 adaptives set to defaults
Zone 0B Head 01 adaptives set to defaults
Zone 0C Head 00 adaptives set to defaults
Zone 0C Head 01 adaptives set to defaults
Zone 0D Head 00 adaptives set to defaults
Zone 0D Head 01 adaptives set to defaults
Zone 0E Head 00 adaptives set to defaults
Zone 0E Head 01 adaptives set to defaults
Zone 0F Head 00 adaptives set to defaults
Zone 0F Head 01 adaptives set to defaults
Head Mask FFFF -
Read Bias - Head    0 1 2 3
                  9 9

HiTemp Bias Head    0 1 2 3
                  9 9
Head Mask FFFF - Switch to full int.
            Spin Ready
Ref Trk Tan Timing Skew (h0 to h0) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h0) = 0000 servo clocks.
Ref Trk Tan Timing Skew (h0 to h1) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h1) = 0000 servo clocks.
Ref Trk Tan Timing Skew (h0 to h2) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h2) = 0000 servo clocks.
Ref Trk Tan Timing Skew (h0 to h3) = 0000 servo clocks.
ID-OD Delta Timing Skew (h0 to h3) = 0000 servo clocks.
Calibrating Physical Track 0 on heads 0 thru 1

Radial Offset Table:

Head 0 Offset = 0
Head 1 Offset = 0
Head 2 Offset = 0
Head 3 Offset = 0

SkpCylList deleted
Sys= 0F68E-0F70D 0280 SPTK on sys trks
<empty>
drive must be reformatted
Skipping MDW oversample s/n cylinders.
Zone 00:  00018 - 00BE8  1100 (044C) 683.439
Zone 01:  00BE9 - 027FE  1056 (0420) 666.63
Zone 02:  027FF - 04707  1026 (0402) 646.275
Zone 03:  04708 - 06CA3 990 (03DE) 622.431
Zone 04:  06CA4 - 08B66 953 (03B9) 602.353
Zone 05:  08B67 - 0A479 916 (0394) 580.392
Zone 06:  0A47A - 0C405 880 (0370) 545.882
Zone 07:  0C406 - 0D99A 836 (0344) 527.59
Zone 08:  0D99B - 0ECD9 806 (0326) 506.144
Zone 09:  0ECDA - 10337 770 (0302) 480.724
Zone 0A:  10338 - 11397 733 (02DD) 461.672
Zone 0B:  11398 - 12854 691 (02B3) 437.423
Zone 0C:  12855 - 13F38 660 (0294) 410.353
Zone 0D:  13F39 - 14AE7 623 (026F) 396.401
Zone 0E:  14AE8 - 155D6 605 (025D) 383.316
Zone 0F:  155D7 - 16358 572 (023C) 363.922
Sys= 0F68E-0F70D 0280 SPTK on sys trks
Total LBAs = 095333FC
EP=1, TA=1, HiGain=1, OTRd=1, Early Rd=0, Splash=1, Reload=1, NPML=1, MRBias=1
Bst/Zap=1, SrvoThrsh=1, RunOut=1, MaxECC=1, ECC 2=1, ECC 1=1, ECC 0=1
Data=FF, Write=80, ID=FF
No entries in Log
All Hds 0-1, All Cyls 00018-16358, Rnd data

Performing AFC Zone Cal

我看不懂这些信息。
Head Mask FFFF -
Read Bias - Head    0 1 2 3
                  9 9

HiTemp Bias Head    0 1 2 3
                  9 9
这些我看不懂；请朋友们帮我看看。这个我砍成功了吗？开SF后面有什么多ERRO 13。。。。。