st340015a ux盘维修

ninghong · 发表于 2009-3-23 12:34:33

此盘是有很多红绿块，想跑自检，我是从N7跑的，结果在08就停掉了，
大家看看这个盘还有救吧，认盘是很快的，
N50,,22
T>N7
T>W
T>Key 04h Ld, Rev 03.15.0169.19
Key 0Ch Ld, Rev 6E.C2.06.62
Key 09h Ld, Rev 14.F2
Key 0Eh Ld, Rev 74.00
Code - 70  Track 000069.0.204  Sns 000  Rty FFFF.67.80  Rtf 3004
T>Interface task reset
Hd Msk 0A00 - Switch to full int.
               Ready
C2 - ST340015A(S) Grand 2A3, Head 12
ROM.02.03
Key 29h Ld, Rev 00.00.0000.11
Key 01h Ld, Rev 03.01.0174.19
Key 11h Ld, Rev 03.01.0174.19
Key 03h Ld, Rev 03.01.0174.19
Key 0Ch Ld, Rev 6E.C2.06.62
Key 09h Ld, Rev 14.F2
Key 0Eh Ld, Rev 74.00
Begin Test 07
UStack=AE00
HEAD  1x WEIGHTS    2x WEIGHTS    3x WEIGHTS    24x WEIGHTS
00 -1DA6 -111D    1069 -001C    026D -013A    0041  0114
The AFC  1x sum of squares weight limit is HEX 2710
The AFC  2x sum of squares weight limit is HEX 1388
The AFC  3x sum of squares weight limit is HEX 1388
The AFC 24x sum of squares weight limit is HEX 1388
UStack=AE00
OkEnd Test 07
Begin Test 0C
UStack=AE00
Tm B5
00C7h
01F5h
__________Open Loop_________
OD TRK  00000100
01B169FC239B3732FFBB332D02AC960F000A%
026027C12530A839000826210448239B000C%
04CB79EA25B9C3DC020CC66704D979A6000E%
0624390927296B8303012A0806513E1B0010%
081A6088284AA5D7049396E0077D7DD60012%
0A5B4C27298F63A70670F17008CD37400014%
02B6484F0BA273B001A2D07903760FC40016%
03B822F80BE40912028DC67A03BBFC9A0018%
04BA94930C13E1B80375476803EDE3EE001A%

后面到这里就不走了
Stack=AE00
OkEnd Test 1D
Begin Test 08
               Not Power Cycling
UStack=AE00
MR=0 TA=0 FcFb=1 OTRd=0 EarlyRd=0 Splash=1 Rload=1 VGA=1
ForcedSync=1 Burnish=1 FIR=1 RunOut=1 MaxECC=1 ECC2=1 ECC1=1 ECC0=1
Data=FF Write=80 GlobalData=00 RetryMode=00
Code - 18  Track 00109E.0.010  Sns 897  Rty 27FF.FF.80  Rtf FA03
Code - 1B  Track 007128.0.09E  Sns B8C  Rty 27FF.FF.80  Rtf 0000
Age=08 Type=E0 MxCyl=017391 MxHd=0 MxSct=000 BSz=0800 TCode=0000 Ovly=00A7
Age=08 Type=E0 MxCyl=017391 MxHd=0 MxSct=000 BSz=0800 TCode=0000 Ovly=00A7

syzdq · 发表于 2009-3-23 16:18:49

08一般要跑好几个小时，应该还在走，你要按“.”才能知道有没有死。

ninghong · 发表于 2009-3-25 09:44:34

跑了12多个小时，跑到32了，等了好久看不到一个数据，，因为是关了机在跑所以没有记录，也不知道还会不会跑下去，，，

ninghong · 发表于 2009-3-25 10:28:48

Interface task reset

Ref 01D8 - Hd Msk 0A00 - Switch to full int.
Ready
C2 - ST340015A(S) Grand 2A3, Head 12
ROM.02.03
Key 29h Ld, Rev 00.00.0000.11
Key 01h Ld, Rev 03.01.0174.19
Key 11h Ld, Rev 03.01.0174.19
Key 03h Ld, Rev 03.01.0174.19
Key 0Ch Ld, Rev 6E.C2.06.62
Key 09h Ld, Rev 14.F2
Key 0Eh Ld, Rev 74.00
Begin Test 32
UStack=AE00
MR=0 TA=1 FcFb=0 OTRd=0 EarlyRd=0 Splash=0 Rload=0 VGA=0
ForcedSync=0 Burnish=0 FIR=0 RunOut=0 MaxECC=0 ECC2=0 ECC1=1 ECC0=0
Data=00 Write=00 GlobalData=00 RetryMode=00
Write unsafe is now disabled.
Write unsafe is now enabled.

Not Power Cycling