希捷ST3160815AS 7200.10维修之路

chenjunfeng50 · 发表于 2015-5-22 15:47:06

本帖最后由 chenjunfeng50 于 2015-5-22 15:51 编辑

先上图

这个盘已经搞了有个把月了，原先是无法分区．

这个是维修的记录文件．看结果应该已经成功完成了，
估计是我备份的固件有问题．

log.zip (166.79 KB, 下载次数: 44)
这是我原盘备份出来的文件

ST160G原盘备份.zip (539.6 KB, 下载次数: 65)
除了ROM，其它几个文件大小都是320KB，

我用的软件是STC513

STC513.zip (455.38 KB, 下载次数: 120)

备份都是按教程一步一步，而且都显示完成的．怎么会有问题呢？
数据线用的是CH341A编程器转TTL＋自制的连接线

chenjunfeng50 · 发表于 2015-5-22 15:55:15

Eng Rev = .0C4
Compat/Hardware = .6B1
NHAWK2HD - 1_Disk 3.AAC  03-27-07_13:06 AAC,NH_1D_2H_S,6D
CERT Rev = .082
NONE
Mask Rom Rev = S-42
Orig Code = AAC6D0

T>
手动输入命令：%
:5000000803000001  AX`5RA1T6MD'  "000000000000"131CA-13347
SRAM Ovly = Diag

T>Age=50 Type=03 MxCyl=2206D MxHd=1 MxSct=339 BSz=008M TCode=01FF0000 ThermFlts=0000

T>
手动输入命令：/C
/C
C>
手动输入命令：D
D
Command Inactive - No VALID Cert Code Detected
C>
正在获取保留区地址......完成！((
正在份析，请稍候........完成！
T>
手动输入命令：/C
/C
C>
手动输入命令：D
D
Cert Table loaded
02,83,84,03,06,07,90,93,98,9C,AA,81,09,74,F4,0F,82,94,56,99,
10,11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,2A,DA,DC,D6,D7,
D8,D9,7C,B9,7D,78,58,23,8F,31,AB,32,AB,33,AB,34,AB,36,A8,37,
3A,8A,3B,3C,3D,3E,A9,3F,20,77,9D,74,E0,87,88,41,4B,44,48,49,
53,4A,4D,8B,61,28,62,29,63,59,85,35,6F,4E,00
C>(Begin Test 02
Current FS Buffer usage: 12800 bytes

FS_INODE_TABLE_BUFFER: b0f
FS_DIR_ENTRY_BUFFER: b11
FS_SCRATCH_BUFFER: b13
FS_INDIR_BLOCKS_BUFFER: b15
FS_BUFFER: b25

ASCII logging on
Requested Mode:
D0
Applied Mode:
D0
Quiet Seek

                  Not Power CyclingFormats Saved

Nominal Formats Selected

Temp Diode 74
( 40 C )

Preamp Registers
Reg  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F
4C 03 6A 02 25 00 00 00 2F 42 41 02 00 58 D6 70
                  Not Power Cycling
Zones 0-F,  Heads 0-1, adaptives set to defaults
HM
Read Bias - Head    0 1 2 3
                  12 D

Buzz Age=02 Type=00 MxCyl=2206D MxHd=1 MxSct=339 BSz=008M TCode=00000000 ThermFlts=0000
HM SFI
!
ASCII logging off

Cylinder ID->OD Bias OD->ID Bias
00200       0047          0038
00600       0046          002B
00A00       0043          0024  ..............................................................................................................................................................................................................................................................................................................................................................................................................................................
OkEnd Test 6F
Begin Test 4E
ASCII logging on
                  Not Power CyclingASCII logging off
ASCII logging on
Log 02 - Health 0000 - HlthDtl 0000 - Time = 00:41:14 Log Type = 01
Log 83 - Health 0000 - HlthDtl 0000 - Time = 00:07:56 Log Type = 01
Log 84 - Health 0000 - HlthDtl 0000 - Time = 00:00:20 Log Type = 01
Log 03 - Health 0000 - HlthDtl 0000 - Time = 00:10:47 Log Type = 01
Log 06 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 07 - Health 0000 - HlthDtl 0000 - Time = 00:00:18 Log Type = 01
Log 90 - Health 0000 - HlthDtl 0000 - Time = 00:00:31 Log Type = 01
Log 93 - Health 0000 - HlthDtl 0000 - Time = 00:00:36 Log Type = 01
Log 98 - Health 0000 - HlthDtl 0000 - Time = 00:00:32 Log Type = 01
Log 9C - Health 0000 - HlthDtl 0000 - Time = 00:00:33 Log Type = 01
Log AA - Health 0000 - HlthDtl 0000 - Time = 00:00:35 Log Type = 01
Log 81 - Health 0000 - HlthDtl 0000 - Time = 00:18:03 Log Type = 01
Log 09 - Health 0000 - HlthDtl 0000 - Time = 00:20:11 Log Type = 01
Log 74 - Health 0000 - HlthDtl 0000 - Time = 00:15:59 Log Type = 01
Log F4 - Health 0000 - HlthDtl 0000 - Time = 00:00:46 Log Type = 01
Log 0F - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 82 - Health 0000 - HlthDtl 0000 - Time = 00:01:28 Log Type = 01
Log 94 - Health 0000 - HlthDtl 0000 - Time = 00:00:15 Log Type = 01
Log 56 - Health 0000 - HlthDtl 0000 - Time = 00:03:59 Log Type = 01
Log 99 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 10 - Health 0000 - HlthDtl 0000 - Time = 00:00:31 Log Type = 01
Log 11 - Health 0000 - HlthDtl 0000 - Time = 00:00:27 Log Type = 01
Log 12 - Health 0000 - HlthDtl 0000 - Time = 00:00:30 Log Type = 01
Log 13 - Health 0000 - HlthDtl 0000 - Time = 00:00:27 Log Type = 01
Log 14 - Health 0000 - HlthDtl 0000 - Time = 00:00:30 Log Type = 01
Log 15 - Health 0000 - HlthDtl 0000 - Time = 00:00:29 Log Type = 01
Log 16 - Health 0000 - HlthDtl 0000 - Time = 00:00:33 Log Type = 01
Log 17 - Health 0000 - HlthDtl 0000 - Time = 00:00:30 Log Type = 01
Log 18 - Health 0000 - HlthDtl 0000 - Time = 00:00:30 Log Type = 01
Log 19 - Health 0000 - HlthDtl 0000 - Time = 00:00:31 Log Type = 01
Log 1A - Health 0000 - HlthDtl 0000 - Time = 00:00:31 Log Type = 01
Log 1B - Health 0000 - HlthDtl 0000 - Time = 00:00:28 Log Type = 01
Log 1C - Health 0000 - HlthDtl 0000 - Time = 00:00:31 Log Type = 01
Log 1D - Health 0000 - HlthDtl 0000 - Time = 00:00:26 Log Type = 01
Log 1E - Health 0000 - HlthDtl 0000 - Time = 00:00:29 Log Type = 01
Log 2A - Health 0000 - HlthDtl 0000 - Time = 00:00:33 Log Type = 01
Log DA - Health 0000 - HlthDtl 0000 - Time = 00:00:05 Log Type = 01
Log DC - Health 0000 - HlthDtl 0000 - Time = 00:00:05 Log Type = 01
Log D6 - Health 0000 - HlthDtl 0000 - Time = 00:00:04 Log Type = 01
Log D7 - Health 0000 - HlthDtl 0000 - Time = 00:00:04 Log Type = 01
Log D8 - Health 0000 - HlthDtl 0000 - Time = 00:00:07 Log Type = 01
Log D9 - Health 0000 - HlthDtl 0000 - Time = 00:00:06 Log Type = 01
Log 7C - Health 0000 - HlthDtl 0000 - Time = 00:00:11 Log Type = 01
Log B9 - Health 0000 - HlthDtl 0000 - Time = 00:00:41 Log Type = 01
Log 7D - Health 0008 - HlthDtl 0000 - Time = 00:00:25 Log Type = 01
Log 78 - Health 0040 - HlthDtl 0000 - Time = 00:00:04 Log Type = 01
Log 58 - Health 0000 - HlthDtl 0000 - Time = 00:07:40 Log Type = 01
Log 23 - Health 0000 - HlthDtl 0000 - Time = 00:04:11 Log Type = 01
Log 8F - Health 0000 - HlthDtl 0000 - Time = 00:04:52 Log Type = 01
Log 31 - Health 0000 - HlthDtl 0000 - Time = 03:13:39 Log Type = 02
Log AB - Health 0000 - HlthDtl 0000 - Time = 00:00:02 Log Type = 01
Log 32 - Health 0000 - HlthDtl 0000 - Time = 03:20:00 Log Type = 02
Log AB - Health 0000 - HlthDtl 0000 - Time = 00:00:02 Log Type = 01
Log 33 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 02
Log AB - Health 0000 - HlthDtl 0000 - Time = 00:00:02 Log Type = 01
Log 34 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 02
Log AB - Health 0000 - HlthDtl 0000 - Time = 00:00:02 Log Type = 01
Log 36 - Health 0000 - HlthDtl 0000 - Time = 00:05:43 Log Type = 02
Log A8 - Health 0008 - HlthDtl 0000 - Time = 00:01:06 Log Type = 02
Log 37 - Health 0000 - HlthDtl 0000 - Time = 00:09:44 Log Type = 02
Log 3A - Health 0000 - HlthDtl 0000 - Time = 01:36:50 Log Type = 02
Log 8A - Health 0000 - HlthDtl 0000 - Time = 00:10:24 Log Type = 01
Log 3B - Health 0000 - HlthDtl 0000 - Time = 00:37:11 Log Type = 02
Log 3C - Health 0000 - HlthDtl 0000 - Time = 00:00:00 Log Type = 02
Log 3D - Health 0000 - HlthDtl 0000 - Time = 00:00:00 Log Type = 02
Log 3E - Health 0000 - HlthDtl 0000 - Time = 00:00:00 Log Type = 02
Log A9 - Health 0008 - HlthDtl 0000 - Time = 00:00:03 Log Type = 01
Log 3F - Health 0000 - HlthDtl 0000 - Time = 00:00:40 Log Type = 01
Log 20 - Health 0000 - HlthDtl 0000 - Time = 00:12:30 Log Type = 01
Log 77 - Health 0000 - HlthDtl 0000 - Time = 00:01:22 Log Type = 01
Log 9D - Health 0000 - HlthDtl 0000 - Time = 00:00:59 Log Type = 01
Log 74 - Health 0000 - HlthDtl 0000 - Time = 00:15:59 Log Type = 01
Log E0 - Health 0000 - HlthDtl 0000 - Time = 00:31:15 Log Type = 01
Log 87 - Health 0000 - HlthDtl 0000 - Time = 00:20:21 Log Type = 01
Log 88 - Health 0040 - HlthDtl 0000 - Time = 00:00:04 Log Type = 01
Log 41 - Health 0000 - HlthDtl 0000 - Time = 00:04:34 Log Type = 01
Log 4B - Health 0000 - HlthDtl 0000 - Time = 00:02:44 Log Type = 01
Log 44 - Health 0000 - HlthDtl 0000 - Time = 00:06:57 Log Type = 01
Log 48 - Health 0000 - HlthDtl 0000 - Time = 00:31:14 Log Type = 01
Log 49 - Health 0000 - HlthDtl 0000 - Time = 00:46:30 Log Type = 01
Log 53 - Health 0000 - HlthDtl 0000 - Time = 00:07:23 Log Type = 01
Log 4A - Health 0000 - HlthDtl 0000 - Time = 00:00:18 Log Type = 01
Log 4D - Health 0000 - HlthDtl 0000 - Time = 00:05:04 Log Type = 01
Log 8B - Health 0000 - HlthDtl 0000 - Time = 00:00:10 Log Type = 01
Log 61 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 28 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 62 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 29 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 63 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 59 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 85 - Health 0000 - HlthDtl 0000 - Time = 00:00:27 Log Type = 01
Log 35 - Health 0000 - HlthDtl 0000 - Time = 00:03:59 Log Type = 01
Log 6F - Health 0000 - HlthDtl 0000 - Time = 00:00:51 Log Type = 01
Total Cert Time = 14:58:54
ASCII logging off
                        Power Cycling

************* ASCII LOG OVERFLOW ****************

Test=50, Feature=0, cumhlth=0048, curhlth=0048
OkEnd Test 50

T>
至此，自校应该成功完成了，但是却回写不了ATA和VEN，一直在F模式．
原来的固件可能已经提取不了了吧？？现在用同型号的其它盘的再试试．．

chenjunfeng50 · 发表于 2015-5-22 20:29:31

现在正在用这个固件自校中..........

3.AAC.zip (888.29 KB, 下载次数: 84)

Age=00 Type=00 MxCyl=00013065 MxHd=00 MxSct=280 BSz=008M TCode=00000000
F>
F>
F>
正在份析，请稍候........完成！
转换至F级...........成功！
正在加载APP.........成功！
正在加载CERT........成功！
正在加载TABLE.......成功！
T>(
T>Eng Rev = .0C4
Compat/Hardware = .6A1
NHAWK1HD - 1_Disk 3.AAD  03-27-07_13:06 AAC,NH_1D_1H_S,6D
CERT Rev = .082
.082
Mask Rom Rev = S-42
Orig Code = AAC6D0

T>
手动输入命令：V4
V4
Alt Defect List
Num Entries = 0000 Checksum = 0000
T>
手动输入命令：/C
/C
C>
手动输入命令：D
D
02,83,84,03,06,07,90,93,98,9C,AA,81,09,74,F4,0F,82,94,56,10,
11,12,13,14,15,16,17,18,19,1A,1B,1C,1D,1E,2A,DA,DC,D6,D7,D8,
D9,7C,B9,7D,78,58,23,8F,31,AB,32,AB,33,AB,34,AB,36,A8,37,3A,
8A,3B,3C,3D,3E,A9,3F,20,77,9D,74,E0,87,88,41,4B,44,48,49,53,
4A,4D,8B,61,28,62,29,63,59,85,35,6F,4E,00
C>Age=60 Type=00 MxCyl=00000 MxHd=0 MxSct=000 BSz=008M TCode=00000000 ThermFlts=0000

C>
手动输入命令：/T
/T
T>
手动输入命令：N50,,22
N50,,22
Wrong data format. Write Adaptives rejected
Code - FD  Track 00000(12EE7).0.000  Sns 000  Rty 027F.FF.80FF  Rtf 1800  LBA 00000000
T>Age=50 Type=00 MxCyl=00000 MxHd=0 MxSct=000 BSz=008M TCode=00000000 ThermFlts=0000

T>
手动输入命令：;
Age=50 Type=00 MxCyl=00000 MxHd=0 MxSct=000 BSz=008M TCode=00000000 ThermFlts=0000

T>
手动输入命令：#
#
Enter Drive S/N
手动输入命令：Ctrl+V
Command Rejected

Enter Packwriter S/N
手动输入命令：5RA1T6MD
5RA1T6MD
T>
手动输入命令：#
#
Enter Drive S/N
手动输入命令：5RA1T6MD
5RA1T6MD
Enter Packwriter S/N
手动输入命令：5RA1T6MD
5RA1T6MD
T>
手动输入命令：N02,,22
N02,,22
T>Age=02 Type=00 MxCyl=00000 MxHd=0 MxSct=000 BSz=008M TCode=00000000 ThermFlts=0000

T>
手动输入命令：Ctrl+T
(Begin Test 02
Current FS Buffer usage: 12800 bytes

FS_INODE_TABLE_BUFFER: b0f
FS_DIR_ENTRY_BUFFER: b11
FS_SCRATCH_BUFFER: b13
FS_INDIR_BLOCKS_BUFFER: b15
FS_BUFFER: b25

ASCII logging on
Requested Mode:
D0
Applied Mode:
D0
Quiet Seek

                  Not Power Cycling
Formats Saved

Nominal Formats Selected

Temp Diode 7F
( 36 C )

Preamp Registers
Reg  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F
4C 23 33 02 B9 00 00 00 2D 42 41 02 00 40 C0 70
                  Not Power Cycling
Zones 0-F,  Heads 0-1, adaptives set to defaults
HM
Read Bias - Head    0 1 2 3
                  D  12

Buzz HM SFI
!
ASCII logging off

Cylinder ID->OD Bias OD->ID Bias
00200       0063          0054
00600       005C          0043

hzxok · 发表于 2015-5-23 02:05:10

没看完你第一次的维修记录就知道你会犯大多数人都会犯的错！关键不是固件，固件能到50就能出盘，是方法不对，网上的教材都没有具体说明9 10的盘SF完后，回写ATA后断电还是会到F级的技术。我是自己自学的，经过多次实验才真的掌握9 10的技巧。不免费教，有需要就联系我，不相信就当我没有说！

chenjunfeng50 · 发表于 2015-5-23 08:54:38

hzxok 发表于 2015-5-23 02:05
没看完你第一次的维修记录就知道你会犯大多数人都会犯的错！关键不是固件，固件能到50就能出盘，是方法不对 ...

大师辛苦啊，半夜还在论坛啊？？？你先跟我说说我备份的固件是否有问题，现在用的固件大小是这样的

chenjunfeng50 · 发表于 2015-5-24 13:18:14

在经过了１５多个小时的SF后，终于停在了Age=50.注意看了这个固件是没有99的，56后直接是10，也就是中间不会自停的。
ASCII logging off

                        Power CyclingTest=6f, Feature=0, cumhlth=0058, curhlth=0000
OkEnd Test 6F
Begin Test 4E
ASCII logging on
                  Not Power Cycling
ASCII logging off
ASCII logging on
Log 02 - Health 0000 - HlthDtl 0000 - Time = 00:38:33 Log Type = 01
Log 83 - Health 0000 - HlthDtl 0000 - Time = 00:07:50 Log Type = 01
Log 84 - Health 0000 - HlthDtl 0000 - Time = 00:00:22 Log Type = 01
Log 03 - Health 0000 - HlthDtl 0000 - Time = 00:10:51 Log Type = 01
Log 06 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 07 - Health 0000 - HlthDtl 0000 - Time = 00:00:18 Log Type = 01
Log 90 - Health 0000 - HlthDtl 0000 - Time = 00:00:31 Log Type = 01
Log 93 - Health 0000 - HlthDtl 0000 - Time = 00:00:36 Log Type = 01
Log 98 - Health 0000 - HlthDtl 0000 - Time = 00:00:33 Log Type = 01
Log 9C - Health 0000 - HlthDtl 0000 - Time = 00:00:34 Log Type = 01
Log AA - Health 0000 - HlthDtl 0000 - Time = 00:00:35 Log Type = 01
Log 81 - Health 0000 - HlthDtl 0000 - Time = 00:18:57 Log Type = 01
Log 09 - Health 0000 - HlthDtl 0000 - Time = 00:20:31 Log Type = 01
Log 74 - Health 0000 - HlthDtl 0000 - Time = 00:16:11 Log Type = 01
Log F4 - Health 0000 - HlthDtl 0000 - Time = 00:00:46 Log Type = 01
Log 0F - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 82 - Health 0000 - HlthDtl 0000 - Time = 00:01:29 Log Type = 01
Log 94 - Health 0000 - HlthDtl 0000 - Time = 00:00:17 Log Type = 01
Log 56 - Health 0000 - HlthDtl 0000 - Time = 00:03:57 Log Type = 01
Log 10 - Health 0000 - HlthDtl 0000 - Time = 00:00:30 Log Type = 01
Log 11 - Health 0000 - HlthDtl 0000 - Time = 00:00:28 Log Type = 01
Log 12 - Health 0000 - HlthDtl 0000 - Time = 00:00:29 Log Type = 01
Log 13 - Health 0000 - HlthDtl 0000 - Time = 00:00:27 Log Type = 01
Log 14 - Health 0000 - HlthDtl 0000 - Time = 00:00:30 Log Type = 01
Log 15 - Health 0000 - HlthDtl 0000 - Time = 00:00:30 Log Type = 01
Log 16 - Health 0000 - HlthDtl 0000 - Time = 00:00:33 Log Type = 01
Log 17 - Health 0000 - HlthDtl 0000 - Time = 00:00:30 Log Type = 01
Log 18 - Health 0000 - HlthDtl 0000 - Time = 00:00:30 Log Type = 01
Log 19 - Health 0000 - HlthDtl 0000 - Time = 00:00:31 Log Type = 01
Log 1A - Health 0000 - HlthDtl 0000 - Time = 00:00:31 Log Type = 01
Log 1B - Health 0000 - HlthDtl 0000 - Time = 00:00:29 Log Type = 01
Log 1C - Health 0000 - HlthDtl 0000 - Time = 00:00:31 Log Type = 01
Log 1D - Health 0000 - HlthDtl 0000 - Time = 00:00:26 Log Type = 01
Log 1E - Health 0000 - HlthDtl 0000 - Time = 00:00:29 Log Type = 01
Log 2A - Health 0000 - HlthDtl 0000 - Time = 00:00:32 Log Type = 01
Log DA - Health 0000 - HlthDtl 0000 - Time = 00:00:05 Log Type = 01
Log DC - Health 0000 - HlthDtl 0000 - Time = 00:00:05 Log Type = 01
Log D6 - Health 0000 - HlthDtl 0000 - Time = 00:00:04 Log Type = 01
Log D7 - Health 0000 - HlthDtl 0000 - Time = 00:00:04 Log Type = 01
Log D8 - Health 0000 - HlthDtl 0000 - Time = 00:00:07 Log Type = 01
Log D9 - Health 0000 - HlthDtl 0000 - Time = 00:00:06 Log Type = 01
Log 7C - Health 0000 - HlthDtl 0000 - Time = 00:00:11 Log Type = 01
Log B9 - Health 0000 - HlthDtl 0000 - Time = 00:00:39 Log Type = 01
Log 7D - Health 0008 - HlthDtl 0000 - Time = 00:00:26 Log Type = 01
Log 78 - Health 0040 - HlthDtl 0000 - Time = 00:00:04 Log Type = 01
Log 58 - Health 0000 - HlthDtl 0000 - Time = 00:07:36 Log Type = 01
Log 23 - Health 0000 - HlthDtl 0000 - Time = 00:04:11 Log Type = 01
Log 8F - Health 0000 - HlthDtl 0000 - Time = 00:04:52 Log Type = 01
Log 31 - Health 0000 - HlthDtl 0000 - Time = 03:21:05 Log Type = 02
Log AB - Health 0000 - HlthDtl 0000 - Time = 00:00:02 Log Type = 01
Log 32 - Health 0000 - HlthDtl 0000 - Time = 03:19:30 Log Type = 02
Log AB - Health 0000 - HlthDtl 0000 - Time = 00:00:02 Log Type = 01
Log 33 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 02
Log AB - Health 0000 - HlthDtl 0000 - Time = 00:00:02 Log Type = 01
Log 34 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 02
Log AB - Health 0000 - HlthDtl 0000 - Time = 00:00:02 Log Type = 01
Log 36 - Health 0000 - HlthDtl 0000 - Time = 00:06:32 Log Type = 02
Log A8 - Health 0008 - HlthDtl 0000 - Time = 00:01:06 Log Type = 02
Log 37 - Health 0000 - HlthDtl 0000 - Time = 00:12:31 Log Type = 02
Log 3A - Health 0000 - HlthDtl 0000 - Time = 01:37:01 Log Type = 02
Log 8A - Health 0010 - HlthDtl 0000 - Time = 00:10:29 Log Type = 01
Log 3B - Health 0000 - HlthDtl 0000 - Time = 00:45:09 Log Type = 02
Log 3C - Health 0000 - HlthDtl 0000 - Time = 00:00:00 Log Type = 02
Log 3D - Health 0000 - HlthDtl 0000 - Time = 00:00:00 Log Type = 02
Log 3E - Health 0000 - HlthDtl 0000 - Time = 00:00:00 Log Type = 02
Log A9 - Health 0008 - HlthDtl 0000 - Time = 00:00:03 Log Type = 01
Log 3F - Health 0000 - HlthDtl 0000 - Time = 00:00:34 Log Type = 01
Log 20 - Health 0000 - HlthDtl 0000 - Time = 00:12:38 Log Type = 01
Log 77 - Health 0000 - HlthDtl 0000 - Time = 00:01:22 Log Type = 01
Log 9D - Health 0000 - HlthDtl 0000 - Time = 00:01:17 Log Type = 01
Log 74 - Health 0000 - HlthDtl 0000 - Time = 00:16:11 Log Type = 01
Log E0 - Health 0000 - HlthDtl 0000 - Time = 00:30:50 Log Type = 01
Log 87 - Health 0000 - HlthDtl 0000 - Time = 00:20:24 Log Type = 01
Log 88 - Health 0040 - HlthDtl 0000 - Time = 00:00:04 Log Type = 01
Log 41 - Health 0000 - HlthDtl 0000 - Time = 00:04:31 Log Type = 01
Log 4B - Health 0000 - HlthDtl 0000 - Time = 00:02:44 Log Type = 01
Log 44 - Health 0000 - HlthDtl 0000 - Time = 00:06:57 Log Type = 01
Log 48 - Health 0000 - HlthDtl 0000 - Time = 00:32:28 Log Type = 01
Log 49 - Health 0000 - HlthDtl 0000 - Time = 00:46:30 Log Type = 01
Log 53 - Health 0000 - HlthDtl 0000 - Time = 00:07:30 Log Type = 01
Log 4A - Health 0000 - HlthDtl 0000 - Time = 00:00:18 Log Type = 01
Log 4D - Health 0000 - HlthDtl 0000 - Time = 00:07:02 Log Type = 01
Log 8B - Health 0000 - HlthDtl 0000 - Time = 00:00:11 Log Type = 01
Log 61 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 28 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 62 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 29 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 63 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 59 - Health 0000 - HlthDtl 0000 - Time = 00:00:01 Log Type = 01
Log 85 - Health 0000 - HlthDtl 0000 - Time = 00:00:27 Log Type = 01
Log 35 - Health 0000 - HlthDtl 0000 - Time = 00:03:57 Log Type = 01
Log 6F - Health 0000 - HlthDtl 0000 - Time = 00:00:51 Log Type = 01
Total Cert Time = 15:19:47
ASCII logging off

                        Power Cycling

************* ASCII LOG OVERFLOW ****************

Test=50, Feature=0, cumhlth=0058, curhlth=0058
OkEnd Test 50

T>Age=50 Type=FF MxCyl=22B50 MxHd=1 MxSct=000 BSz=008M TCode=00FF0001 ThermFlts=0000

T>Age=50 Type=FF MxCyl=22B50 MxHd=1 MxSct=000 BSz=008M TCode=00FF0001 ThermFlts=0000

T>
手动输入命令：R
R
T>
手动输入命令：Ctrl+C
(P)SATA Reset
Unable To Load Overlay 00|0014
(
T>
正在获取缓冲区地址......完成！
正在获取保留区地址......完成！
请先加载Cert模块！(按^R加载Cert)VALID Cert Disk Code Detected - Revision # .082

T>
T>Eng Rev = .0C4
Compat/Hardware = .6A1
NHAWK1HD - 1_Disk 3.AAD  03-27-07_13:06 AAC,NH_1D_1H_S,6D
CERT Rev = .082
.082
Mask Rom Rev = S-42
Orig Code = AAC6D0

T>
请先加载Cert模块！(按^R加载Cert)VALID Cert Disk Code Detected - Revision # .082

T>
T>
手动输入命令：^R
Time = 02:29:22 Log Type = 01
请先加载Cert模块！(按^R加载Cert)
VALID Cert Disk Code Detected - Revision # .082

T>
T>
请先加载Cert模块！(按^R加载Cert)VALID Cert Disk Code Detected - Revision # .082

T>
T>
请先加载Cert模块！(按^R加载Cert)VALID Cert Disk Code Detected - Revision # .082

T>
T>
转换至F级...........成功！
正在加载APP.........成功！
正在加载CERT........成功！
正在加载TABLE.......成功！
T>
请先加载Cert模块！(按^R加载Cert)INVALID Cert Disk Code - ROM Resident Revision Required: AAC6D0

T>
T>
手动输入命令：^R
Time = 00:00:16 Log Type = 00
Age=60 Type=00 MxCyl=00000 MxHd=0 MxSct=000 BSz=008M TCode=00000000 ThermFlts=0000

T>N50,,22
Wrong data format. Write Adaptives rejected
Code - FD  Track FFFFF(12F4D).0.1A8  Sns FFF  Rty 027F.FF.80FF  Rtf 1800  LBA 00000850
T>
T>Age=50 Type=00 MxCyl=00000 MxHd=0 MxSct=000 BSz=008M TCode=00000000 ThermFlts=0000

T>
请先加载Cert模块！(按^R加载Cert)INVALID Cert Disk Code - ROM Resident Revision Required: AAC6D0

T>
T>

********************************************
硬盘容量对应LBA值：
40G  LBA: 78165360 Hex: 4A8B570
60G  LBA: 117231408 Hex: 6FCCF30
80G  LBA: 156301488 Hex: 950F8B0
120G  LBA: 234441648 Hex: DF94BB0
160G  LBA: 312581808 Hex: 12A19EB0
200G  LBA: 390826800 Hex: 174B8B30
250G  LBA: 488397168 Hex: 1D1C5970
320G  LBA: 625142448 Hex: 2542EAB0
400G  LBA: 781653600 Hex: 2E971660
500G  LBA: 976773168 Hex: 3A386030
750G  LBA: 1464843750  Hex: 574FBDE6
  1T  LBA: 1953525168  Hex: 74706DB0
1.5T  LBA: 2930277168  Hex: AEA87B30
  2T  LBA: 3907029167  Hex: E8E088AF
********************************************
(Reset
4096k x 16 DRAM
NHAWK - 1_Disk S-42 03-27-07_11:48

Buzz HM SFI
!
(P)SATA Reset
Unable To Load Overlay 00|0014
(
T>Age=50 Type=FF MxCyl=22B50 MxHd=1 MxSct=000 BSz=008M TCode=00FF0001 ThermFlts=0000

T>Pgm=00 Trk=FFFFF(131B7:00[1467D]).0(0).001(FFF) Zn=0 Err=00 ErCt=0000 Hlth=0058 CHlth=0000 Ready LBA=0000047B

T>
请先加载Cert模块！(按^R加载Cert)VALID Cert Disk Code Detected - Revision # .082

T>
T>/
T>R1
T>R2
T>
正在获取缓冲区地址......完成！
T>
正在获取保留区地址......完成！
T>
请先加载Cert模块！(按^R加载Cert)VALID Cert Disk Code Detected - Revision # .082

T>
T>
请先加载Cert模块！(按^R加载Cert)VALID Cert Disk Code Detected - Revision # .082

T>
T>
请先加载Cert模块！(按^R加载Cert)VALID Cert Disk Code Detected - Revision # .082

T>
T>
手动输入命令：N4F,,22
N4F,,22
T>Age=4F Type=FF MxCyl=22B50 MxHd=1 MxSct=000 BSz=008M TCode=00FF0001 ThermFlts=0000

T>
请先加载Cert模块！(按^R加载Cert)VALID Cert Disk Code Detected - Revision # .082

T>
T>
转换至F级...........成功！
正在加载APP.........成功！
正在加载CERT........成功！
正在加载TABLE.......成功！
T>Age=60 Type=00 MxCyl=00000 MxHd=0 MxSct=000 BSz=008M TCode=00000000 ThermFlts=0000

T>N50,,22
Wrong data format. Write Adaptives rejected
Code - FD  Track 00000(12EE7).0.000  Sns 000  Rty 027F.FF.80FF  Rtf 1800  LBA 00000000
T>
T>
手动输入命令：E4E
E4E
No log 4E on disk
T>(Reset
4096k x 16 DRAM
NHAWK - 1_Disk S-42 03-27-07_11:48

Buzz HM SFI
!
(P)SATA Reset
Unable To Load Overlay 00|0014
(
T>Eng Rev = .0C4
Compat/Hardware = .6A1
NHAWK1HD - 1_Disk 3.AAD  03-27-07_13:06 AAC,NH_1D_1H_S,6D
CERT Rev = .082
NONE
Mask Rom Rev = S-42
Orig Code = AAC6D0

T>
请先加载Cert模块！(按^R加载Cert)VALID Cert Disk Code Detected - Revision # .082

T>
T>
现在的问题是回写ATA和ID的问题，老是提示加载Cert模块！但是明明加载了也没有用，又是论坛上一阵查找，发现有好多人说STC是不能回写ATA的，但也有人说是可以的，难道是网上下载的STC软件不一样？？听说“春华希捷专修程序”可以回写ATA等，但是搜索春华希捷专修程序发现不那么容易下载，要么要太多的金币，要么有病毒。搞到后来电脑中了木马，蓝屏死机了好几次。唉！！！！

chenjunfeng50 · 发表于 2015-5-24 17:58:12

终于弄明白了，是我备份的固件有问题。用STC备份下来的几个固件文件，除了ROM是64K正常的，其它几个都是320K大小，在用F级引导的时候加载TABLE.TRC的时候会提示文件太大，所以不能引导和回写。
在论坛上下载了这个固件

3.AAC.zip (888.29 KB, 下载次数: 108) 终于成功把盘完美修复了。下面说一下经过：
１、刷ROM芯片，因为几个固件文件是互相关联的，所以要一起换。在刷ROM时，其实又遇到问题了，造成了盘不转，软件端没有任何反应了。最后拆板拆ROM芯片25F512AN，用编程器写发现我的CH341A编程器只能读出，却无法擦除和写入。最后没有办法，用手头的T80-75HCP写入新的ROM数据上试验，上电就听到盘转起来了，一阵激动！之后也能正常通讯了。
2、用STC中的“F级引导”加载新的APP,CERT,TABLE.都显示完成。
３、启动SF。新的固件中没有９９这个过程，所以能一直做到结束，用时Total Cert Time = 15:19:47
４、回写固件中的ATA,ID.在这一步摸索了很久。最后用的这个软件成功写入。

STComTools.zip (427.24 KB, 下载次数: 134)
这是操作流程记录文件

2zjz.zip (175.77 KB, 下载次数: 103)
硬盘完美修复

chenjunfeng50 · 发表于 2015-5-24 18:12:56

说是完美，还有一点遗憾就是硬盘型号变了

其实难点是在回写ATA与ID这一步，
终于松了一口气，不花钱修复了生平第一个硬盘．

附上我回写ATA与ID的操作记录：
Eng Rev = .0C4
Compat/Hardware = .6A1
NHAWK1HD - 1_Disk 3.AAD  03-27-07_13:06 AAC,NH_1D_1H_S,6D
CERT Rev = .082
NONE
Mask Rom Rev = S-42
Orig Code = AAC6D0

T>Age=50 Type=FF MxCyl=22B50 MxHd=1 MxSct=000 BSz=008M TCode=00FF0001 ThermFlts=0000

T>
正在获取缓冲区地址......完成！
T>
正在获取保留区地址......完成！
T>
请先加载Cert模块！(按^R加载Cert)
T>
正在加载CERT........成功！
T>
正在获取模块地址........完成！
T>
正在写入数据......完成！
T>Eng Rev = .0C4
Compat/Hardware = .6A1
NHAWK1HD - 1_Disk 3.AAD  03-27-07_13:06 AAC,NH_1D_1H_S,6D
CERT Rev = .082
NONE
Mask Rom Rev = S-42
Orig Code = AAC6D0

T>(Reset
4096k x 16 DRAM
NHAWK - 1_Disk S-42 03-27-07_11:48

Buzz HM SFI
!
(P)SATA Reset

Stuff Was Unreadable3.AAD  03-27-07_13:06 AAC,NH_1D_1H_S,6D
(
T>

T>Eng Rev = .0C4
Compat/Hardware = .6A1
NHAWK1HD - 1_Disk 3.AAD  03-27-07_13:06 AAC,NH_1D_1H_S,6D
CERT Rev = .082
NONE
Mask Rom Rev = S-42
Orig Code = AAC6D0

T>(Reset
4096k x 16 DRAM
NHAWK - 1_Disk S-42 03-27-07_11:48

Buzz HM SFI
!
(P)SATA Reset

Stuff Was Unreadable3.AAD  03-27-07_13:06 AAC,NH_1D_1H_S,6D
(
T>

lchllinely · 发表于 2015-5-26 09:58:44

型号其实在你开始自校前就应该自己改一下。

论坛游民 · 发表于 2015-5-28 16:18:16

认真发帖不错啊很好的教程

[讨论] 希捷ST3160815AS 7200.10维修之路

点评