10代S-6D 校准出现 Parm Range Err

yudi05 · 发表于 2012-8-19 15:06:43

本帖最后由 yudi05 于 2012-8-19 15:09 编辑

今天跑了块10代厚盘，GALAXY2D S-6D 开始时指令模式认盘，挂电脑BIOS下不认，无奈跑校准

可没想到无论T级还是F级都是下面的样子，高手们给看看是怎么回事

对了，单头、多头、砍0跑都一样

F级引导到T  查看段位信息是

T>/2
/2
2>x
x

Head 00
Zone 00:  16552 - 16551 660 (0294) 489.081
Zone 01:  16552 - 16551 660 (0294) 489.081
Zone 02:  16552 - 16551 660 (0294) 489.081
Zone 03:  16552 - 16551 660 (0294) 489.081
Zone 04:  16552 - 16551 660 (0294) 489.081
Zone 05:  16552 - 16551 660 (0294) 489.081
Zone 06:  16552 - 16551 660 (0294) 489.081
Zone 07:  16552 - 16551 660 (0294) 489.081
Zone 08:  16552 - 16551 660 (0294) 489.081
Zone 09:  16552 - 16551 660 (0294) 489.081
Zone 0A:  16552 - 16551 660 (0294) 489.081
Zone 0B:  16552 - 16551 660 (0294) 489.081
Zone 0C:  16552 - 16551 660 (0294) 489.081
Zone 0D:  16552 - 00000 660 (0294) 489.081
Reserve:  15D47 - 15EC6 640 (0280) 489.81
Total KBAs = 00000000

难道是磁头被卡住了？

然后：

T>Eng Rev = .0H8
Compat/Hardware = .6D0
GALAXY2D - 1_Disk 3.ACH  02-15-07_12:45 ACH,GX_2D_4H_P,4H
CERT Rev = .0BJ
.0BJ
Mask Rom Rev = S-6D
Orig Code = ACH4H1 TONKA2_GX_4H1.0H8.0BJ

T>N2,,22
N2,,22
T>(Begin Test 02
Current FS Buffer usage: 12288 bytes

FS_INODE_TABLE_BUFFER: 4aa
FS_DIR_ENTRY_BUFFER: 4ac
FS_SCRATCH_BUFFER: 4ae
FS_INDIR_BLOCKS_BUFFER: 4b0
FS_BUFFER: 4c0

ASCII logging on

                  Not Power Cycling
Formats Saved

Nominal Formats Selected

Temp Diode 76
( 39 C )

Preamp Registers
Reg  1  2  3  4  5  6  7  8  9  A  B  C  D  E  F
4B 02 65 02 98 00 00 00 51 42 4E 0E 10 01 C1 50

                  Not Power Cycling
Zones 0-D,  Heads 0-0, adaptives set to defaults
Parm Range Err
Parm Range Err
Parm Range Err
Parm Range Err
Parm Range Err
.........
不停一直出