|
|
发表于 2012-6-9 13:19:21
|
显示全部楼层
-------------------------------------------------------------------------------- Format Partition (Level T 'm')--------------------------------------------------------------------------------
Description:
This command formats the specified partition.
Quick Help:
"FormatPartition, m[Partition],[FormatOpts],[DefectListOpts],[MaxWrRetryCnt],[MaxRdRetryCnt],\n\r"
"[MaxEccTLevel],[MaxCertifyTrkRewrites],[ValidKey],[DataPattern]";
Input Parameters:
0 - Partition Number.
This parameter specifies the media partition to be formatted.
0 = User Partition
1 = System Partition
Type: Unsigned 8-bit value
Range: 0 or 1
Default: 0
1 - Format Options.
This parameter is a bit significant value that selects the following options:
Bits 31-6: not used
Bit 5: Enable SeaCOS XF Space Format.
This bit is only valid when the User Partition is selected. If this
bit is equal to 1, the the Format Partition command will only format
SeaCOS Extended File (XF) space.
NOTE: This feature can be enabled or disabled at compile-time. Use
the quick help to determine whether your code supports this feature.
Bit 4: Enable Zone Re-format Skipping.
If this bit is equal to 1, then the Format Partition command will
enable the zone re-format skipping mode during the format operation.
With this mode enabled, the format operation will not re-format
a zone if grown defects were found in the zone.
NOTE: This feature can be enabled or disabled at compile-time. Use
the quick help to determine whether your code supports this feature.
Bit 3: Enable Event-based Format Logging.
If this bit is equal to 1, then the Format Partition command will
display information about error events that occur during the format
operation. This information will be displayed as interim status as
these events occur.
NOTE: This feature can be enabled or disabled at compile-time. Use
the quick help to determine whether your code supports this feature.
Bit 2: Disable User Partition Certify.
This bit is only valid when the User Partition is selected. If this
bit is equal to 1, media certification and defect deallocation will
be disabled.
Bit 1: Disable User Partition Format.
This bit is only valid when the User Partition is selected. If this
bit is equal to 1, the User Partition sectors will not be written
with a constant data pattern.
Bit 0: Corrupt User Partition Primary Defects.
This bit is only valid when the User Partition is selected. If this
bit is equal to 1, the primary defective sectors will be corrupted.
Type: Unsigned 32-bit value
Range: 0 or 0xFFFFFFFF
Default: 0 (Enable User partition Certify,
Enable User Partition Format,
Don't Corrupt Primary Defects)
2 - Defect List Options.
This parameter is a bit significant value that selects the following options:
Bits 31-3: not used
Bit 2: Process the Active Error Log.
This bit is only valid when the User Partition is selected. If this
bit is equal to 1, the Format Client Defect List will be written with
contents of the Active Error Log and the option to process the Client
Defect List will be enabled. If there is no Active Error Log or there
are no R/W-related entries in the Active Error Log, then this bit will
be ignored.
Bit 1: Process Primary Defect Lists.
This bit is only valid when the User Partition is selected. If this
bit is equal to 1, the the Primary Defect Lists will be used when
creating the defect list to be used by the format operation.
Bit 0: Process Grown Defect Lists.
This bit is only valid when the User Partition is selected. If this
bit is equal to 1, the the Grown Defect Lists will be used when
creating the defect list to be used by the format operation.
Type: Unsigned 32-bit value
Range: 0 or 0xFFFFFFFF
Default: 0x00000003 (Process Grown Defect Lists,
Process Primary Defect Lists,
Do not process the Active Error Log)
3 - Maximum Write Retry Count.
If this parameter is entered, the maximum write retry count will be set to the
specified value. This parameter is only valid when the User Partition is being
formatted (Parameter 0 is equal to 0). If this parameter is not entered, the
maximum write retry count will not be changed.
Type: Unsigned 16-bit value
Range: 0 or 0xFFFF
Default: None.
4 - Maximum Read Retry Count.
If this paremeter is entered, the maximum read retry count will be set to the
specified value. This parameter is only valid when the User Partition is being
formatted (Parameter 0 is equal to 0). If this parameter is not entered, the
maximum read retry count will not be changed.
Type: Unsigned 16-bit value
Range: 0 or 0xFFFF
Default: None.
5 - Maximum ECC T-Level.
If this paremeter is entered, the maximum ECC T-Level will be set to the specified
value. This parameter is only valid when the User Partition is being formatted
(Parameter 0 is equal to 0). If this parameter is not entered, the ECC T-Level
will not be changed.
Type: Unsigned 16-bit value
Range: 0 or 0xFFFF
Default: None.
6 - Track Rewrite During Certify Retry Threshold.
If this parameter is entered, it specifies the maximum number of rewrite retries
to be performed during the user partition certification pass.
Type: Unsigned 16-bit value
Range: 0 or 0xFFFF
Default: None. If this parameter is not entered, the default value recommended
by the R/W Firmware will be used.
7 - Valid Command Key.
For a User Partition format, this parameter must be equal to 22 Hex. If this
parameter is not equal to 22 Hex, the command will not be executed.
For a System Partition format, this parameter must be equal to DD Hex. If this
parameter is not equal to DD Hex, the command will not be executed.
Type: Unsigned 8-bit value
Range: 0x22 or 0xDD
Default: None
8 - Data Pattern For Format.
This parameter specifies the data pattern to be used when formatting the specified
partition. If this parameter is not entered, the specified partition will be
formatted with a 0x00000000 data pattern.
Type: Unsigned 32-bit value
Range: 0 or 0xFFFFFFFF
Default: 0x00000000.
Output Data:
If the error occurred while processing the defect lists, the following additional
information will be displayed.
"Process Defect List Error"
"R/W Sense cccccccc, R/W Error dddddddd, List Offset eeeeeeee, File Error ffffffff"
where
cccccccc is the sense status that was returned by the R/W subsystem
dddddddd is the error code that was returned by the R/W subsystem
eeeeeeee is the offset of the defect list entry at which the error occurred
ffffffff is the error code that was returned by the system information manager (SIM)
If the error occurred during the format operation, the following additional information
will be displayed.
"User Partition Format Failed - Elapsed Time c"
"R/W Sense dddddddd, R/W Error eeeeeeee, File Error ffffffff"
"Blk Addr gggggggg, Blk Addr Type hh, Cyl iiiiiiii, Hd jj";
where
c is the amount of time that has elapsed since the format operation was started
dddddddd is the sense status that was returned by the R/W subsystem
eeeeeeee is the error code that was returned by the R/W subsystem
ffffffff is the error code that was returned by the system information manager (SIM)
gggggggg is the R/W block address at which the error occurred
hh is the R/W block address type at which the error occurred
iiiiiiii is the R/W cylinder address at which the error occurred
jj is the R/W head address at which the error occurred
If no error occurred and the format operation is still in progress, the following
information will be displayed.
"Max Wr Retries = cc, Max Rd Retries = dd, Max ECC T-Level = ee, Max Certify Rewrite Retries = ffff"
"User Partition Format gg% complete, Zone hh, Pass ii, LBA jjjjjjjj, ErrCode kkkkkkkk, Elapsed Time l"
where
cc is the maximum write retry count to be used
dd is the maximum read retry count to be used
ee is the maximum ECC T-Level to be used
ffff is the certify rewrite rety threshold
gg is the percent of the format operation that has been completed
hh is the data zone that is currently being formatted
ii is the number of the current pass through the data zone
jjjjjjjj is the last LBA that was formatted
kkkkkkkk is the error code that was reported by the R/W subsystem
l is the amount of time that has elapsed since the format operation was started
If no error occurred, the format operation is still in progress, a format event occurs,
and format event reporting is enabled, the following information will be displayed.
"Event: Media Write Start, aaa Format, Zone bb, Start Blk cccccccc, Num Sectors dddddddd"
or
"Event: Write Xfer, Start Blk cccccccc, Len eeeeeeee, Next Blk ffffffff, Erc gggggggg, Stat hh"
or
"Event: Media Certify Start, New Format, Zone bb, Start Blk cccccccc, Num Sectors dddddddd"
or
"Event: Certify Xfer, Start Blk cccccccc, Len eeeeeeee, Next Blk ffffffff, Erc gggggggg, Stat hh"
or
"Event: Unrec Err, LBA iiiiiiii, PBA jjjjjjjj, Erc gggggggg, Trk llll, Hd mm, Sctr nn, Wdg oo, ZnGrp pp, Zn qq, DOS: rr/ss/tt"
"Event: Unrec Err, LBA iiiiiiii, PBA jjjjjjjj, Erc gggggggg, Trk llll, Hd mm, Sctr nn, Wdg oo, Zn qq, DOS: rr/ss/tt"
"Event: Unrec Err, LBA iiiiiiii, PBA jjjjjjjj, Erc gggggggg, Trk llll, Hd mm, Sctr nn, Wdg oo, ZnGrp pp, Zn qq"
"Event: Unrec Err, LBA iiiiiiii, PBA jjjjjjjj, Erc gggggggg, Trk llll, Hd mm, Sctr nn, Wdg oo, Zn qq"
NOTES: ZnGrp information is only available on drives supporting VBAR
DOS information is only available on drives supporting Directed Offline Scan
or
"Event: Cert Trk Rewrite, Retry Blk kkkkkkkk, Len eeeeeeee, Next Blk ffffffff, Erc gggggggg, Stat hh"
or
"Event: Cert Trk Rewrite Cntr Update, Cnt 0001"
where
aaa indicates whether this is a "New Format" or a "Reformat"
bb is the zone
cccccccc is the starting block
dddddddd is the number of blocks to be formatted
eeeeeeee is the length of the transfer
ffffffff is the next starting block
gggggggg is the error code that was reported by the R/W subsystem
hh is the read/write status
iiiiiiii is the logical block address (LBA)
jjjjjjjj is the physical block address (PBA)
kkkkkkkk is the block which causes the rewrite retry
llll is the track on which the error occurred
mm is the head on which the error occurred
nn is the sector on which the error occurred
oo is the wedge on which the error occurred
pp is the zone group in which the error occurred
qq is the zone in which the error occurred
rr is the DOS scan unit associated with the error
ss is the DOS relative cylinder in scan unit associated with the error
tt is the DOS surface cylinder unit associated with the error
If no error occurred and the format operation has successfully completed, the following
information will be displayed.
" User Partition Format Successful - Elapsed Time m"
where
m is the amount of time that has elapsed since the format operation was started
If at least one zone re-format was skipped then the following will also be
displayed upon successful completion of the format:
"Zone re-format was skipped."
Examples:
Example #1:
Perform a "quick format" (process defect lists, clear format corrupt, do not write
or certify the drive)
F3 T>m0,6,,,,,,22
Example #2:
Perform a "quick format" (don't process defect lists i.e. unslip and unalt, do not
write or certify the drive)
F3 T>m0,6,0,,,,,22
Example #3:
Perform a format with the default data pattern 0x00000000 and certify with event
reporting enabled:
F3 T>m0,8,,,,,,22
Example #4:
Perform a format and certify with event reporting enabled, set max write retries
to 16, set max read retry count to 8, max ECC T-Level to 0, and track rewrite
during certify retry threshold to 20:
F3 T>m0,8,,10,8,0,14,22
Example #5:
Perform a format with user input data pattern 0xFFFFFFFF and certify with event
reporting enabled:
F3 T>m0,8,,,,,,22,ffffffff
Revision History:
0001.0000 Initial revision.
0001.000X Added ability to enable and display event-based output.
0011.000X Combined the PSG Diagnostic Error Codes (PSGDEC) and the Diagnostic External
Test Service Error Codes (DETSEC) into a single set of Diagnostic Error Codes
(DiagError).
0012.000X Added additional parameter 8 for users to input data pattern for format. The
default data pattern is 0x00000000 instead of the 0x77777777 for the User
Partition and 0xFFFFFFFF for the System Partition.
0012.001X Added option to process the Active Error Log.
Note on Minor Rev:
----.ZZZX ZZZ represents the minor rev base value.
X represents set of conditional feature flags.
- If bit 0 of X is set, then the ability to enable and display
event-based output is supported.
- If bit 1 of X is set, then the ability to enable zone re-format
skipping and output command result information if at least one
zone re-format was skipped is supported.
- If bit 2 of X is set, then the ability to format only SeaCOS
Extended File (XF) space is supported.
- (Bit 3 of X is reserved for future conditional features.)
|
|
狗仔卡
提升卡
置顶卡
喧嚣卡
变色卡
显身卡
希捷硬盘数据恢复之磁头组件烧毁污染篇
北京某高级数据恢复系列教程
SeaTools for Windows(中文版)
MHDD 6.6 一鍵快修
电子产品散热设计深度探讨
【新手看老鸟闪】西数模块定义直观图
硬盘维修以及数据恢复合集
真正希捷F3批量维修程序 同时操作6个盘 可
58GrenadaBP2家族三角板盘1ERxx系列硬砍0头
WD 28（PST）模块简要说明