|
楼主 |
发表于 2015-9-18 21:22:53
|
显示全部楼层
WD10JPV-22JC3T0
微码是
Drive Physical Parameters Data Table
Format version of return sector: = 0x2
Controller firmware version: = 16.14G
Servo firmware version: = NA.18
Overlay firmware version: = 16.14G
Format firmware version: = A1.004
Channel firmware version: = G.00031A
Product ID: = 0x34
Drive platter count: = 0
Physical head count: = 0
Virtual head count: = 1
Depop Head Info: = H0 Depoped
Drive type: = Mobile 2 1/2 inch
Servo zone count: = 61
Servo wedges per track: = 296
Number of negative cylinders: = 256
Spindle RPM: = 5419
Physical number of user cylinders: = 0
Cylinder wedge skew: = 0x1F
Head wedge skew: = 0x4E
Cluster wedge skew: = 0x70
Code Residence: = Serial Flash.
PCBA Type: = Non-Entek
Interface type: = 0x2
Controller chip vendor ID: = 0x0
Controller chip revision No.: = 0xA5C0
Microprocessor vendor ID: = 0x0
Microprocessor revision No.: = 0xA5C0
Channel chip vendor ID: = 0x0
Channel chip revision No.: = 0x0
PreAmp chip vendor ID: = 0x1
Preamp revision No.: = 0x0
Power IC vendor ID: = 0x0
Power IC revision No.: = 0x8021
#Interleaves in OTF ECC correction: = 0x0
Bytes per Interleave OTF correction: = 0x0
F/W Burst correction count: = 0
Correction Bytes in Read Long: = 0
Max VSC Transfer block count: = 0x100
Jumper Settings: = 0x80
Remaining Relocation sectors: = 0x0
DCM Component: =
DCM Vendor: =
Original FTS build date: =
Reconfiguration FTS build date: =
DRIVE DATA TABLES
=================
Format Version........ = 0x2
Controller FW Rev .... = 16.14G
Servo FW Rev ......... = NA.18
Overlay FW Rev ....... = 16.14G
Drive Type ........... = 3 Mobile 2.5 Inch
lang/mgboy 21:19:49
Drive Build Information
-----------------
Product ID ........... = 0x16FE (TAHOE_LT)
Drive Platter Count... = 0
No. of Physical Hds... = 0 (including Depops)
No. of Virtual Hds.... = 1
Depop Bit Map (Hex)... = 0x0 (Bit 0= Hd used)
No. of Zones ......... = 61
No. of Servo Wedges... = 296
No. of Neg. Cyls ..... = 256
Spindle RPM .......... = 5419
Phy. No of User Cyls = 0
Cylinder Wedge Skew. = 31
Head Skew ............ = 78
Cluster Skew ......... = 112
Rom Type = 5 (Serial Flash)
PCBA Type = 0 Entek
PCBA Revision = 0
Interface Type = 2 (Serial ATA)
Drive Parts Information
-----------------
Ctrl Chip Vendor ... = 0x0
Ctrl Chip Rev ...... = 0xA5C0
MicroP Vendor ...... = 0x0
MicroP Rev ......... = 0xA5C0
Channel Chip Vendor. = 0x0
Channel Chip Rev.... = 0x0
Preamp Vendor ...... = 0x1
Preamp Rev ......... = 0x0
PowerIC Vendor ..... = 0x0
PowerIC Rev ........ = 0x8021
Error Correction Information
-----------------
No. of Interleaves .......... = 0
OTF Corr. Span in Bytes ..... = 0
Max FW Corr. Span in Bytes... = 0
No. of ECC Bytes + CRC Bytes. = 0
Feature Flags ............... = 0xDC3FDB6
Jumper Settings
-----------------
Jumper Setting Value..... = 0x80
Bit 0 (Master Jumper).... = OFF
Bit 1 (Slave Jumper)..... = OFF
Bit 1 (CSEL Jumper)...... = OFF
ReloList File Information
-----------------
No. of Relocations ................ = 0
No. of Tares....................... = 0
No. of Ftares ..................... = 0
No. of Possible Remaining Relos ... = 0
No. of Consumed spares............. = 0
Last LBA of Spare Pool............. = 0x0
Drive Format Information
-----------------
Tracks per inch (in KTPI)............ = 0
Area Density in 100MB (per platter).. = 0
Format Type.......................... = 0 (primary format)
SATA IPM Timers
-----------------
Partial................. = 5 ms
Slumber................. = 100 ms
Drive Built Data
-----------------
DCM...................... =
FTS Date ................ =
FTS Reconfig Date........ =
微码 = 00160014 |
|