WD SA偏移后写不了固件了

telbbs · 发表于 2006-11-11 16:14:23

因为SA有缺陷
分别把坏的模块偏移到另一个负磁道
之后在检查固件的时候
前面的O头出错了
---------------------------------------------------------------
TRACKS DIRECTORY
Version : 15DBM
27/ 2/ 1
Copy number    Location       State
-------------------------------------------------------
1       C:-1  H: 0       Read Error
2       C:-1  H: 1       OK

Modules amnount: 58

ZONE TABLE
Amount of zones: 21
  # Start cylinder    End cylinder Sectors amount
----------------------------------------------------------------
  1       -32          -1          504
  2       0          1119          648
  3    1120          2143          637

------------------------------------------------------------------------------------
现在回写不了DIR了
我把25偏移到了11后
-11也开始有缺陷了
原来-11完好的
怎么办呀

TRACKS DIRECTORY
Version : 15DBM
27/ 2/ 1
Copy number    Location       State
-------------------------------------------------------
1       C:-1  H: 0       Read Error
2       C:-1  H: 1       OK

Modules amnount: 58

ZONE TABLE
Amount of zones: 21
  # Start cylinder    End cylinder Sectors amount
----------------------------------------------------------------
  1       -32          -1          504
  2       0          1119          648
  3    1120          2143          637
  4    2144          4031          648
  5    4032          6687          637
  6    6688       10079          648
  7    10080       11263          637
  8    11264       14079          633
  9    14080       16895          633
10    16896       18399          624
11    18400       20479          600
12    20480       23039          576
13    23040       24127          552
14    24128       25215          540
15    25216       26207          528
16    26208       28191          504
17    28192       29919          480
18    29920       30719          468
19    30720       31807          452
20    31808       32991          432
21    32992       35522          400

CONFIGURATION SECTOR
27/ 2/ 1
Copy number    Location       State
-------------------------------------------------------
1       C:-2  H: 0       OK
2       C:-2  H: 1       OK

Description data  :
Model          : WDC WD200EB-00BHF0
Serial number    : WD-WMA6K4690105
Logical parameters  : Cyl : 38792  Head : 16  Sec : 63
No software isolated heads
Master-password : WDCWDCWDCWDCWDCWDCWDCWDCWDCWDCWD (ESTABLISHED)
User-password  :                      (NOT ESTABLISHED)
Security level  : high

DCM Info
10/ 1/ 1
Copy number    Location       State
-------------------------------------------------------
1       C:-2  H: 0       OK
2       C:-2  H: 1       OK

  1  4  7  ;  ?       ""
                        &
            !  #  %  (  *  -  /  3
  6  :  ?       ""
                  &
         !  #  %  '  *  ,  .  1  4  7
  ;  ?       ""

Ver. Info
5/12/ 0
Copy number    Location       State
-------------------------------------------------------
1       C:-2  H: 0       OK
2       C:-2  H: 1       OK

ROM version       : r
Link table version :
Disk FW version    : De

PList
5/12/ 0
Copy number    Location       State
-------------------------------------------------------
1       C:-2  H: 0       OK
2       C:-2  H: 1       OK

Defects amount: 785

GList
27/ 2/ 1
Copy number    Location       State
-------------------------------------------------------
1       C:-2  H: 0       OK
2       C:-2  H: 1       OK

Defects amount: 301

FIRMWARE MODULES

#  ID  Cyl Head Sec Length Date Ver  C.S. State
--------------------------------------------------------------
1  42  42  -2  0 0 1 27/ 2/ 1  0100  65 OK
   42  -2  1 0 1 27/ 2/ 1  0100  65 OK

2  43  43  -2  0 2  170 5/12/ 0  0100  DF OK
   43  -2  1 2  170 5/12/ 0  0100  DF OK

3  44  44  -2  0  173 8 27/ 2/ 1  0100  78 OK
   44  -2  1  173 8 27/ 2/ 1  0100  78 OK

4  59  59  -2  0  182 4 5/12/ 0  0100  92 OK
   59  -2  1  182 4 5/12/ 0  0100  92 OK

5  20  20  -2  0  187  77 1/ 1/98  0401  66 OK
   20  -2  1  187  77 1/ 1/98  0401  66 OK

6  25  20  -11  0  265  10 1/ 1/98  0401  32  Read Error
   20  -11  1  265  10 1/ 1/98  0401  32  Read Error

telbbs · 发表于 2006-11-11 16:36:50

目前已经无法回写固件了

难道只有SA清零或SA格式化才能回写了吗？

八喜哥指点下