刚在老外家找到的,希望对大家有用Seagate ES.2 7200.11
Unlocking terminal of Seagate ES.2 in BSY/LED:000000CC state for owners of Seagate ES.2 (ST******NS) which are locked in BSY state Rate Topic:Here's what I discovered after many attempts in the last few nights.
Terminal of my 2 ES.2 drives was locked (drives were in BSY state) - every 3-4 seconds I received from their terminal message LED: 000000CC....
Standard solution which is widely known for 7200.11 series (ST******AS) doesn't work for locked ES.2 series (ST******NS) !!!
But i've found a way to unlock terminal of my ES.2 driveswhat allows then to repair hd in a standard way (solution from Yura/Okzo).
1. Disk has to be complete (PCB+rest together), NO isolation between the PCB and the rest
2. In the terminal you will see every few seconds message LED: 000000CC ...
3. between these messages you can unlock the terminal by pushing CTRL+Z. It will show a line: "F3 T>" and it will be Unlocked for about 1 second
4. During that 1 second when you see "F3 T>" message but before you receive next "LED:000000CC..." you must short two points shown in the following image (they are known as "read-channel").
You must hold them short about 20-30 or little more seconds.
If you won't see next "LED:000000CC..." and disk will issue few unpleasant sounds then after some time you'll see in the terminal message "Input Command Eror".
Now the disk's terminal is unlocked!
Still holding those 2 pins short issue command /2 and then Z (they're cAsE sEnSiTiVe!).
When disk's engine will stop you will see message "Spin Down Complete" and now you can release the short between 2 pins.
Next do repair with standard instruction (as for 7200.11) - all below is cAsE sEnSiTiVe!:
F3 2>U
Spin Up Complete
F3 T3>/1
F3 1>N1
F3 1>/
F3 T>m0,2,2,0,0,0,0,22
and wait until you'll get message
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 00, Max Certify Rewrite Retries = 0000
.....
User Partition Format Successful - Elapsed Time 0 mins 05 secs
Good example (also extended) gave aviko, in post number 529 in topic # 128807
It is at: http://www.msfn.org/board/index.php?showto...mp;#entry832876
I am a complete amateur (not DR professional), and of course, give no warranty for the described procedure.
It worked for me and my two ES.2 drives are alive now.
Of course, this procedure or the incorrect use might as well burn your disks and data.
I don't assume responsibility for such cases - everything you do at your own risk.
This procedure of ES.2' terminal unlocking is my own discovery, and I'd like to share this knowledge with other poor owners of bricked (in BSY state) ES.2 disks. 沙发 楼主好贵哦~~ 全英文的 ~~~看不懂~~ 什么东东啊？这么贵~~~ 什么东东啊？这么贵~~~ 这个估计UDMA说明书里早有了 这是什么啊，楼主给个截图 老东西这个价格不值了 太贵了 连说明都没有 看了，确实不值钱了，资料太老了 ，还是F3 T3>/1
F3 1>N1
F3 1>/
F3 T>m0,2,2,0,0,0,0,22