8.01 7200.7 120G老是跑3A而且还不过,
请问这是咱个会事,还过不了,3A又开始跑了,问高手说我的电源没接好,可是电源我整了又整还是不行,肯定不是电源问题.请高手指教 不一定的这两天做了两只0780G串口
都是好多流程都没有LOG
结果都OK! 3A必须做过的,是扫离散的坏扇区。做3A前清一下健康值,或再换个版本试试,还不行就看是哪个头坏扇区记录特别多,就砍了。 谢谢各位,现在好了Begin Test 3A
Not Power Cycling
Zone 3 offset step compensation, writing ZAP IDs...
EP=0, TA=0, HiGain=0, OTRd=0, Early Rd=0, Splash=0, Reload=0, NPML=0, MRBias=0
Bst/Zap=0, SrvoThrsh=0, RunOut=0, MaxECC=0, ECC 2=0, ECC 1=0, ECC 0=1
Data=02, Write=32, ID=FF
Interface task reset
1024k x 16 buffer detected
ALPINE - 1_Disk M-2111-25-03 18:53
Head Mask FFFF - Switch to full int.
Spin Ready
8.5404-04-05 16:21
(P)PATA Reset
Not Interface Age!
VALID Cert Disk Code Detected - Revision # .258
Cert Table loaded
No script first instruction.
No valid SeaDex script on disc.
Begin Test 3A
Not Power Cycling
Zone 3 offset step compensation, writing ZAP IDs...
EP=0, TA=0, HiGain=0, OTRd=0, Early Rd=0, Splash=0, Reload=0, NPML=0, MRBias=0
Bst/Zap=0, SrvoThrsh=0, RunOut=0, MaxECC=0, ECC 2=0, ECC 1=0, ECC 0=1
Data=02, Write=32, ID=FF
Interface task reset
1024k x 16 buffer detected
ALPINE - 1_Disk M-2111-25-03 18:53
Head Mask FFFF - Switch to full int.
Spin Ready
8.5404-04-05 16:21
(P)PATA Reset
Not Interface Age!
VALID Cert Disk Code Detected - Revision # .258
Cert Table loaded
No script first instruction.
No valid SeaDex script on disc.
Begin Test 3A
Not Power Cycling
Zone 3 offset step compensation, writing ZAP IDs...
EP=0, TA=0, HiGain=0, OTRd=0, Early Rd=0, Splash=0, Reload=0, NPML=0, MRBias=0
Bst/Zap=0, SrvoThrsh=0, RunOut=0, MaxECC=0, ECC 2=0, ECC 1=0, ECC 0=1
Data=02, Write=32, ID=FF 原来老是这样显示,我就按网上说的,把8.01的固件换成8.54的果然好多了,但是在3A处还是不过.只是跑得要快点了,砍了最后一个头,并清板,然后,3A在四个小时候就过了,谢谢各位,有论坛真是好啊 08 31 3A 这几个流程要很长时间的! 学习中。学习中。学习中。学习中。学习中。 学习,学习``呵呵` 3A是啥阿?? 看贴不回。。不道德
页:
[1]
2