SCSI 硬盘出现Start United request failed，怎么办
start unit request failed? 怎么解决？用的M15笼子 1.硬盘在SCSI管理器里认不到容量.但能认到型号.状态显示为0FF-LINE.2.系统启动的时候显示:"SCSI Start Unit Request Failed" There are various steps that may resolve the problem:
Unload and try a different tape (Make sure a tape is loaded). Make sure drive loads and unloads properly.
Make sure the unit shows up at boot in the BIOS, under SCSI Adapters and Tape Devices in the control panel if running NT. Make sure drivers are loaded. Remove everything from the SCSI chain except for the tape drive. You can switch the ID of the host adapter and tape drive back and forth to see if priority makes a difference.
Try using Native backup software app if your using a different one or have this option.
This error can be a simple hardware error -- try a different SCSI cable and terminator. Try using an active terminator -- terminate SCSI chain at both ends.
Try to unload tape and power drive off for a few minutes and then power on again to clear volatile memory. 没看懂
请高手指点
硬盘掉线了；
实际是硬盘没有了容量，可以搞定； 'Start Unit Request Failed' Hard Drive Error and Recovery
SCSI (Small Computer System Interface) hard drives possess better performance due to their speed in terms of throughput and rpm (rotations per minute) rating. These hard drives are often used with servers, RAID and JBOD arrays and workstations that require high performance. But sometimes hard drive failure may affect our business critical operations due to drive health issues. Such crashes occur due to hard drive fatigue, component failure and external factors that require Data Recovery service as the solution.
Error Explanation
SCSI hard drives fail to start up when experience physical failure. When the computer system is powered on, SCSI BIOS gets the drive control from system BIOS. This SCSI BIOS sends 'Start Unit Request' to the SCSI devices including SCSI hard drive so that they may start and spin up. Upon successful completion of task, SCSI BIOS gets 'Start Unit Request Completed' plus some additional information from drives in return. But if this task completion command is not received in a specific interval of time by SCSI BIOS, it returns an error message that might occur due to hard drive failure:
"Start Unit Request Failed"
Reasons
- High Condensation and Electronic Failure: In high throughput environment, the major concern with such hard drives is heat. Though SCSI hard drives offer good resistance to heat but when the system is powered off and condensation occurs due to extreme heat, hard drive electronics suffer the most. The electronic components may break down due to high stress conditions making a hard drive useless.
- Mechanical Failure: Hard drives can remain functional and tolerate vibrations till the read/write head works fine. The head crash is characterized by strange noises. Apart from it, other internal failures also create a need for Data Recovery service preferably through Clean Rooms.
The above error message occurs due to hard drive failure and drive recovery service can take care of your precious data by extracting all your data files from the hard disk. But there are other solutions as well, which are:
- User can make a jumper setting so as to ignore SCSI BIOS process. The drive can be set to auto-start in which system starts as it gets power. - User can disable the Unit Request confirmation from drive.
After we suitably apply these procedures, we can get enough time for data backup. However if these are not possible or fruitful, the most appropriate solution is to go for Hard Disk Recovery which is meant to extract lost data under expert supervision and through certified Clean Rooms.
Stellar Information Systems Limited is the number one company in providing high quality Data Recovery service since 1993. The company provides exhaustive Hard Drive Recovery through Class-100 Clean Room facility, advanced set of data extraction procedures and expert professionals. Stellar's Hard Disk Recovery is provided for interfaces including SCSI, SATA, EIDE/ATA-2 and IDE.
Article By K Madhav 八喜帮忙指点一下吧，谢谢啊 你不用发这些文章，你刚开始的描述其实已经知道发生了什么，硬盘出现了故障，不是不想指点，硬件故障这个不是远程能够操作的； 只通过软件能够解决吗？
页:
[1]
2