请教各位大神 WD 3TB 硬盘修复停留在D3的问题
以下是 WD 3TB 硬盘修复停留在D3的问题，请各位指点！整个流程是硬盘自带稍加修改，之前上面的走过一次，后来从C4开始走。
日志如下：
WDC WD3000FYYZ-01UL1B1 FW:01.60Q SN:WD-WCC13136XXXX (ROYL selected) port 0xF0F0
Logical: Cyls 16383, Heads 16, Sectors 63, LBA 1565565872, 801Gb
Controller Buffer Size: 0Kb
Family: Midori (Royl)
2017/6/6 19:31:25 All Steps: 39, Current: 38
2017/6/6 19:37:38 All Steps: 46, Current: 38
2017/6/6 19:38:58 Set SelfScan Step to 31 - OK
2017/6/6 19:39:12 Set SelfScan Step to 31 - OK
2017/6/6 19:39:21 Clear IBI Abort Code - SUCCESS by
2017/6/6 19:39:21 Set SelfScan Step to 31 - OK
2017/6/6 19:39:21 Enable PST Mode - OK
2017/6/6 19:39:39 Power On Reset Immediate - SUCCESS by
2017/6/6 19:40:10 C4 - 磁头读写参数/飞檐高度调整 - SUCCESS by
2017/6/6 19:40:10 B1 - 快速扫描/测试用户区 - Start
2017/6/6 19:58:36 B1 - 快速扫描/测试用户区 - SUCCESS by
2017/6/6 19:58:36 C4 - 磁头读写参数/飞檐高度调整 - Start
2017/6/6 19:58:37 C4 - 磁头读写参数/飞檐高度调整 - SUCCESS by
2017/6/6 19:58:37 D1 - 扫描缺陷(写)并加入LOG - Start
2017/6/9 6:54:45 D1 - 扫描缺陷(写)并加入LOG - SUCCESS by
2017/6/9 6:54:46 DD - 增益校准 - Start
2017/6/9 6:55:22 DD - 增益校准 - SUCCESS by
2017/6/9 6:55:22 DB - 扫描缺陷(读)并加入LOG - Start
2017/6/9 6:55:58 DB - 扫描缺陷(读)并加入LOG - SUCCESS by
2017/6/9 6:55:58 D5 - 测试簇 - Start
2017/6/9 6:56:36 D5 - 测试簇 - SUCCESS by
2017/6/9 6:56:36 D4 - 测试磁道缺陷 - Start
IBI Common Log:
Test Count 14 - 63:50:47
1 B9 B9 0 1 104:55:0704:55:07
2 B9 B9 0 1 100:00:0500:00:05
3 B9 B9 0 1 100:00:0500:00:05
4 B9 B9 0 1 100:00:0500:00:05
5 B9 B9 0 1 100:00:0500:00:05
6 B9 B9 0 1 100:00:0500:00:05
7 B9 B9 0 1 100:00:0500:00:05
8 B9 B9 0 1 100:00:0500:00:05
9 DB DB 0 1 100:00:1100:00:11
10 D1 0 0 1 158:52:4258:52:42
11 DD DD 0 1 100:00:3300:00:33
12 DB DB 0 1 100:00:3200:00:32
13 D5 0 0 1 100:00:3400:00:34
14 D4 D4 0 1 100:00:3300:00:33
Abort Section:
Abort Code: 6, Test ID: 0, Test Status: 0
Current Test ID: 0, Abort Code: 0, Test Status: 0
Soft Error Counter:0, Soft Error Total:0
SPT Defect Statistical Chart
Head 0 = 136530( Tracks: 61287, Sectors: 75243, Max: 136530 )
Head 1 = 136530( Tracks: 80631, Sectors: 55899, Max: 136530 )
Head 2 = 136530( Tracks: 84647, Sectors: 51883, Max: 136530 )
Head 3 = 136530( Tracks: 69952, Sectors: 66578, Max: 136530 )
Head 4 = 136530( Tracks: 89290, Sectors: 47240, Max: 136530 )
Head 5 = 136530( Tracks: 84320, Sectors: 52210, Max: 136530 )
Head 6 = 136530( Tracks: 79193, Sectors: 57337, Max: 136530 )
Head 7 = 136530( Tracks: 72156, Sectors: 64374, Max: 136530 ) 本帖最后由 long597 于 2017-6-14 15:39 编辑
现在处于D3处理扇区数量，已经在这个流程走了4天了，还是没结束。
这啥盘呀这是,你这玩意根本就不对呀 scq330 发表于 2017-6-14 13:23
这啥盘呀这是,你这玩意根本就不对呀
西数 WD3000FYYZ，请大神指点！ 爆头了吧，楼主 本帖最后由 long597 于 2017-6-14 16:22 编辑
laiguanjia 发表于 2017-6-14 15:42
爆头了吧，楼主
磁头完好，我觉得爆表也有可能，坏道确实太多了。有什么好办法？ long597 发表于 2017-6-14 16:20
磁头完好，我觉得爆表也有可能，坏道确实太多了。有什么好办法？
换固件再跑 long597 发表于 2017-6-14 16:20
磁头完好，我觉得爆表也有可能，坏道确实太多了。有什么好办法？
换固件再跑 long597 发表于 2017-6-14 16:20
磁头完好，我觉得爆表也有可能，坏道确实太多了。有什么好办法？
换固件再跑 long597 发表于 2017-6-14 15:35
西数 WD3000FYYZ，请大神指点！
这个盘你这样是修不好的,根本就不是这么一回事...