盘盘1982 发表于 2012-6-29 08:55:24

7200.12不认盘找不到问题

接通电源后显示

Rst 0x10M
Servo Processor Is Reset.
RW: Disc Ctlr Initialization Completed.

ExecuteSpinRequest

(P) SATA Reset

按CTRL+Z无法切换到F3 T>，郁闷啊

miss郭龙 发表于 2018-7-19 21:05:54

建议封禁账号，没找到问题就在论坛里问，解决了直接就走，不分享维修经验。

linwei1234 发表于 2015-11-16 03:19:16

一年都不想告诉,现在也不会告诉吧,多半此人死翘翘了

xinzhiquan526 发表于 2015-8-22 04:36:30

有点分享精神好不好，有问题时求助，问题解决了，交流一下经验嘛

盘盘1982 发表于 2012-6-29 08:56:09

7200.12   320G的

ashytools 发表于 2012-6-29 08:58:12

终端连接的问题。。硬盘OK的。

盘盘1982 发表于 2012-6-29 09:01:42

连接还好，开启硬盘电源时候快速按CTRL能切换到F3，按慢了就没反应了Rst 0x10M
Servo Processor Is Reset.
RW: Disc Ctlr Initialization Completed.

ExecuteSpinRequest

ASCII Diag mode

F3 T>
ASCII Diag mode

F3 T>
ASCII Diag mode

F3 T>
ASCII Diag mode

F3 T>
ASCII Diag mode

F3 T>
(P) SATA Reset

ASCII Diag mode

F3 T>
ASCII Diag mode

F3 T>

就是BIOS里不识盘，晕

盘盘1982 发表于 2012-6-29 09:06:02

F3 T>m0,2,2,0,0,0,0,22
m0,2,2,0,0,0,0,22
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 00, Max Certify Rewrite Retries = not supported

盘盘1982 发表于 2012-6-29 09:06:43

F3 T>m0,2,2,0,0,0,0,22
m0,2,2,0,0,0,0,22
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 00, Max Certify Rewrite Retries = not supported

User Partition Format   3% complete, Zone 00, Pass 00, LBA 000000009A64, ErrCode 00000080, Elapsed Time 0 mins 30 secs      
User Partition Format Successful - Elapsed Time 0 mins 30 secs      
Zone re-format was skipped.

盘盘1982 发表于 2012-6-29 09:27:01

跑成这样了0000AFF500, Len 000FFF00, Next Blk 000000BFF400, Erc 43110081, Stat 01->Ns;->Ns;->Ns;->Ns;s;->Ns;->Ns;s;->Ns;s;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;s;->Ns;s;s;s;s;s;s;->Ns;s;s;s;s;->Ns;->Ns;s;->Ns;->Ns;s;->Ns;->Ns;s;s;s;->Ns;->Ns;->Ns;->Ns;s;->Ns;s;s;s;s;->Ns;s;->Ns;s;s;->Ns;s;->Ns;->Ns;s;s;->Ns;s;s;s;s;s;s;->Ns;->Ns;->Ns;->Ns;
Event: Certify Xfer, Start Blk 000000BFF400, Len 000FFF00, Next Blk 000000CFF300, Erc 43110081, Stat 01->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;
Event: Certify Xfer, Start Blk 000000CFF300, Len 000FFF00, Next Blk 000000DFF200, Erc 43110081, Stat 01->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;s;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;s;
Event: Certify Xfer, Start Blk 000000DFF200, Len 000FFF00, Next Blk 000000EFF100, Erc 43110081, Stat 01->Ns;->Ns;->Ns;
User Partition Format   5% complete, Zone 00, Pass 03, LBA 000000FEF59D, ErrCode 43110081, Elapsed Time 12 mins 00 secs      
Event: Certify Xfer, Start Blk 000000EFF100, Len 000FFF00, Next Blk 000000FFF000, Erc 43110081, Stat 01->Ns;s;->Ns;s;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;
Event: Certify Xfer, Start Blk 000000FFF000, Len 000FFF00, Next Blk 0000010FEF00, Erc 43110081, Stat 01->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;->Ns;
Event: Certify Xfer, Start Blk 0000010FEF00, Len 000FFF00, Next Blk 0000011FEE00, Erc 43110081, Stat 01->Ns;->Ns;

sunlong517 发表于 2012-6-29 09:56:29

这个是pc3000里的指令修吗?我的是直接系统里的指令修 怎么接都是乱码呀

盘盘1982 发表于 2012-6-29 10:41:05

设置38400就不乱了

盘盘1982 发表于 2012-6-29 10:41:46

ser Partition Format39% complete, Zone 05, Pass 01, LBA 00000F040F03, ErrCode 00000080, Elapsed Time 84 mins 30 secs      
Event: Write Xfer, Start Blk 00000EF55774, Len 000FFF00, Next Blk 00000F055674, Erc 00000080, Stat 01
Event: Write Xfer, Start Blk 00000F055674, Len 000FFF00, Next Blk 00000F155574, Erc 00000080, Stat 01
Event: Write Xfer, Start Blk 00000F155574, Len 000FFF00, Next Blk 00000F255474, Erc 00000080, Stat 01q->w
Event: Write Xfer, Start Blk 00000F255474, Len 000FFF00, Next Blk 00000F355374, Erc C4090081, Stat 01
Event: Write Xfer, Start Blk 00000F355374, Len 000FFF00, Next Blk 00000F455274, Erc 00000080, Stat 01qD->S21(01)wqDS21(02)wqDS21(03)wqDS21(04)wqDS21(05)w
Event: Write Xfer, Start Blk 00000F455274, Len 000FFF00, Next Blk 00000F555174, Erc C4030086, Stat 01
User Partition Format39% complete, Zone 05, Pass 01, LBA 00000F5B69C1, ErrCode 00000080, Elapsed Time 85 mins 00 secs      
Event: Write Xfer, Start Blk 00000F555174, Len 000FFF00, Next Blk 00000F655074, Erc 00000080, Stat 01
Event: Write Xfer, Start Blk 00000F655074, Len 000FFF00, Next Blk 00000F754F74, Erc 00000080, Stat 01
Event: Write Xfer, Start Blk 00000F754F74, Len 000FFF00, Next Blk 00000F854E74, Erc 00000080, Stat 01q->w
Event: Write Xfer, Start Blk 00000F854E74, Len 000FFF00, Next Blk 00000F954D74, Erc C4090081, Stat 01
Event: Write Xfer, Start Blk 00000F954D74, Len 000FFF00, Next Blk 00000FA54C74, Erc 00000080, Stat 01
User Partition Format39% complete, Zone 05, Pass 01, LBA 00000FB307C2, ErrCode 00000080, Elapsed Time 85 mins 30 secs      
Event: Write Xfer, Start Blk 00000FA54C74, Len 000FFF00, Next Blk 00000FB54B74, Erc 00000080, Stat 01
Event: Write Xfer, Start Blk 00000FB54B74, Len 000FFF00, Next Blk 00000FC54A74, Erc 00000080, Stat 01
Event: Write Xfer, Start Blk 00000FC54A74, Len 000AD246, Next Blk 00000FD01CBA, Erc 00000080, Stat 01
Event: Media Write Start, New Format, Zone 05, Start Blk 00000DDD3E52, Num Sectors 1F2D068
Event: Write Xfer, Start Blk 00000DDD3E52, Len 000FFF00, Next Blk 00000DED3D52, Erc 00000080, Stat 01
Event: Write Xfer, Start Blk 00000DED3D52, Len 000FFF00, Next Blk 00000DFD3C52, Erc 00000080, Stat 01q->w
Event: Write Xfer, Start Blk 00000DFD3C52, Len 000FFF00, Next Blk 00000E0D3B52, Erc C4090081, Stat 01
User Partition Format39% complete, Zone 05, Pass 02, LBA 00000E178582, ErrCode 00000080, Elapsed Time 86 mins 00 secs      
Event: Write Xfer, Start Blk 00000E0D3B52, Len 000FFF00, Next Blk 00000E1D3A52, Erc 00000080, Stat 01
Event: Write Xfer, Start Blk 00000E1D3A52, Len 000FFF00, Next Blk 00000E2D3952, Erc 00000080, Stat 01
Event: Write Xfer, Start Blk 00000E2D3952, Len 000FFF00, Next Blk 00000E3D3852, Erc 00000080, Stat 01
Event: Write Xfer, Start Blk 00000E3D3852, Len 000FFF00, Next Blk 00000E4D3752, Erc 00000080, Stat 01
Rst 0x10M
Servo Processor Is Reset.
RW: Disc Ctlr Initialization Completed.

ExecuteSpinRequest

(P) SATA Reset

(P) SATA Reset

SIM Error 3005
No HOST FIS-ReadyStatusFlags 2002A1A5


跑到这里停下了。
页: [1] 2 3
查看完整版本: 7200.12不认盘找不到问题